Spade Drill Bit
How To Fit Solid Wood Flooring
How to fit Solid Wood flooring
It is important to start any flooring installation by firstly planning out the room and deciding where to start. Many rooms offer what at first appear to be very complicated situations to overcome. Don’t worry too much about these, all situations have a solution which are covered in this section, alternatively further information can be found in the handy hints and tips section.
Planning:-
When first presented with a room or area which is to be fitted with Solid wood flooring some key factors will help you to decide where to start your installation. Door ways, shape of room and locations of main window are all factors to take into consideration as well as the subfloor (existing floor which is to be covered with Solid wood floor) here are some rules and suggestions:-
Rules –
When laying Solid wood flooring on top of existing floor boards always lay the planks at 90 degrees to the floor boards
It is important not to end up with a piece of flooring at the end of a row which is less than 5cm in length or to have the last row less than 5cm in width. To avoid this measure the room’s width and length and divide the results by the dimensions of the flooring being installed. It may then be necessary to start the first row with a half plank or even to cut the width down to accommodate the area
An expansion joint will need to be inserted into any floor area which is larger than 8m in length or in width, in effect creating two floor areas
Acclimatise the boards in the room they are to be laid in for a minimum of 48 hours. The room should have a relative humidity of between 45% – 65% and a temperature of between 18C – 20C
Suggestions –
It is generally accepted that the best visual effect when installing Solid wood flooring is to lay the boards in the direction of the light source; so towards the main window (not forgetting rule 1 above)
It is also suggested that the floor should run along the longest wall of the room giving the best overall effect. (again take note of rule 1 above)
When laying a floor across a door way it is best practise to start at this point and work back into the room
Installation guide:-
Once your planning stage is complete it is time to prepare the room starting with the subfloor. It is vital that the subfloor is in optimal condition to allow the new floor to perform as expected and help to maintain its longevity
Subfloor preparation –
The main factors to consider are the smoothness, dryness and overall levelness of the floor. If the subfloor is uneven then the new floor will not last long as the pressure on the joints will cause the boards to separate
For concrete floors make sure that they are dry (it takes approx. 1 day per 1mm of wet concrete to be considered dry enough for a Solid wood floor to be installed). The relative humidity of the floor is also vital it should not exceed 85%
For wooden subfloors, ensure there is no movement in the floor. Any loose floor boards should be nailed or screwed securely in place. WBP (water and boil proof) ply can be used over existing floorboards to provide a suitable subfloor surface
All floors must be smooth and level
Finally all debris must be cleaned and the surface of the subfloor must be free from dust and other contaminants
Installation Techniques:-
There are three main ways to install a Solid Wood floor,
Secret nailing
Gluing directly to the subfloor
Installing the Solid wood onto a self adhesive underlay
All of these methods are perfectly acceptable methods of installation for a domestic application, each method has its benefits and draw backs. It is often the subfloor which will help to determine which installation is best suitable.
Installing the floor planks – Secret nailing –
Secret nailing a wooden floor is a method usually chosen when the existing subfloor is wood or when installing directly to joists. Solid wood flooring should have a minimum thickness of 21mm if it is to be fitted directly to joists.
It is possible to use the secret nail technique when the subfloor is concrete or screed. A damp proof membrane (DPM) needs to be placed over the concrete followed by an 18 – 24mm WBP plywood sheet.
Start the first row by loose laying the boards parallel to the wall allowing a 15mm expansion gap. Begin by resting the fitting wedges up against the wall to give you a 15mm gap. This is vital as the Solid boards will expand and contract after installation and if this gap is not present the floor will lift and buckle in the room. The wedges are removed after installation is complete and the gap is covered with either skirting or beading
At the end of the first row you will undoubtedly need to cut a board to length. A good way to measure the length of the board required is to rotate the loose board by 180 degree (facing upwards) so that the tongue is facing the tongue of the previous row. Rest the board next to the first row then mark and cut the boards to size.
(NB. When cutting Solid flooring ensure that a new blade is used)
Once you are happy with the alignment, ‘face nail’ the boards into the subfloor at intervals of 250-300mm or onto every joist. Face nailing is nailing through the top of the planks into the subfloor, counter sink the nails and fill in the dimples with wood filler.
Depending on the tools used and the width of the flooring installed, it may be necessary to face nail two or three rows before secret nailing can begin.
Continue laying rows of planks down ensuring that you keep the 15mm expansion gap around the perimeter of the room. Stagger the boards so that the end joint of each row is further than 150mm apart (brick bond)
Keeping the nails at a distance of 250 – 300mm, secret nail the planks into the subfloor. Secret nailing is a method where planks are secured through the tongue of the boards at a 45 degree angle and counter sunk to allow the groove of the next board to fit tightly. Mechanical nail guns are the best way to achieve professional results and make installation a lot easier.
The final row can be measured and marked to size using the following technique; firstly place the board to be marked directly on top of the last row laid. Place another plank on top of the loose plank but this time have the top plank pushed up against 15mm wedges against the wall to give you the correct measurement allowing for expansion. (be careful not to move the board to be marked) now draw a line along the edge of the top plank marking the board underneath.
The last few rows will also have to be face nailed as there will not be enough room for secret nailing.
Installing the floor planks – Direct gluing –
Direct gluing is a suitable method of installation when fixing on top of a concrete or screed subfloor. One benefit is that the overall height of the new floor is kep to a minimum as there is no need to install an 18mm WBP plywood base. It is also suitable over existing wood floors which are suitably flat and firm.
The subfloor must be flat, firm and level; if necessary a levelling compound may be used. It is important to remember that all subfloors must be dry.
A liquid damp proof membrane must be laid first and allowed to dry.
Using a suitable wood flooring adhesive apply an even coat to the subfloor. A notched trowel held at between 450 and 900 is the best method for this.
Start the first row by laying the boards parallel to the wall allowing a 15mm expansion gap. Begin by resting the fitting wedges up against the wall to give you a 15mm gap. This is vital as the Solid boards will expand and contract after installation and if this gap is not present the floor will lift and buckle in the room. The wedges are removed after installation is complete and the gap is covered with either skirting or beading
At the end of the first row you will undoubtedly need to cut a board to length. A good way to measure the length of the board required is to rotate the loose board by 180 degree (facing upwards) so that the tongue is facing the tongue of the previous row. Rest the board next to the first row then mark and cut the boards to size.
(NB. When cutting Solid flooring ensure that a new blade is used)
After two rows have been successfully installed weigh them down while the glue sets. Any glue which has seeped through to the surface should be removed immediately.
Continue laying rows of planks down ensuring that you keep the 15mm expansion gap around the perimeter of the room. Stagger the boards so that the end joint of each row is further than 150mm apart (brick bond)
Tension straps may be used to hold rows tightly together whilst the glue sets.
The final row can be measured and marked to size using the following technique; firstly place the board to be marked directly on top of the last row laid. Place another plank on top of the loose plank but this time have the top plank pushed up against 15mm wedges against the wall to give you the correct measurement allowing for expansion. (be careful not to move the board to be marked) now draw a line along the edge of the top plank marking the board underneath.
Installing the floor planks – Self adhesive underlay –
Solid flooring can also be laid as a floating floor using a self adhesive underlay. The boards are adhered directly to the underlay which holds the floor together. This method can be used for all subfloor types (following the rules set out above that subfloors be flat, firm and dry) the benefits of the self adhesive underlay is that the room can be used immediately with no drying time required for glue to set.
Lay the underlay at 90 degrees to the direction of the boards ensuring that there are no gaps between sheets but equally important is that the underlay does not overlap. When using the underlay over concrete, first lay a DPM with the edges overlapped by 20cm.
Peel back the foil from the underlay by the width of 2 ½ planks and fold over.
Using the supplied spare foil, lay this over the exposed adhesive surface of the underlay with enough surplus foil facing the wall to fold back over the top of the underlay
Place the fitting wedges up against the wall to give you a 15mm gap. This is vital as the Solid boards will expand and contract after installation and if this gap is not present the floor will lift and buckle in the room. The wedges are removed after installation is complete and the gap is covered with either skirting or beading
Position the first row along the wall and wedges allowing for the expansion gap and ensure that this is perfectly straight. (if the first row is not perfectly straight the entire floor will be ruined) At the end of the first row you will undoubtedly need to cut a board to length. A good way to measure the length of the board required is to rotate the loose board by 180 degree (facing upwards) so that the tongue is facing the tongue of the previous row. Rest the board next to the first row then mark and cut the boards to size
(NB. When cutting Solid flooring ensure that a new blade is used)
Now lay a second row, this will help to stabilise the two rows whilst the foil is removed as well as help to provide a straight line
Once you are satisfied the rows are straight and tightly fitted, peel back the loose foil sheet which will expose the adhesive underlay to the solid wood flooring thus holding the boars in place.
The loose foil may now be discarded. The remaining attached foil will be your work area where new rows will be rested on until you are happy that they are tightly fitted.
Continue to fit the rows down and peel away the foil to fix the boards into place.
The final row can be measured and marked to size using the following technique; firstly place the board to be marked directly on top of the last row laid. Place another plank on top of the loose plank but this time have the top plank pushed up against 15mm wedges against the wall to give you the correct measurement allowing for expansion. (be careful not to move the board to be marked) now draw a line along the edge of the top plank marking the board underneath.
Obstacles –
There are various obstacles you will come across when installing any flooring. The trick is to identify these at the beginning and plan when to tackle them. You do not want to end up at an obstacle where you may need to remove some flooring you have already installed to enable you to deal with the situation.
Door frames are inevitable as almost all rooms will have these. It is necessary to remove a section of architrave and door jam to allow the Solid to be fitted under them, thus hiding the expansion gap away from sight. To do this you will need to place a piece of underlay and an upturned board against the door frame. Using a long saw pressed against the Solid floor begin to cut into the door frame. Make your cut until you reach the wall behind the door frame. Do not worry about cutting into the skirting as the beading will cover this. Remove as much of the door frame as possible so as to allow the right expansion room for the Engineered.
Measure and mark the Solid to fit and then install. When faced with a room where there are doors on both sides of a room and the Solid is installed across the door way it may be necessary to use glue to fit a board at one of these doors. As it is impossible to install the board at 30 degrees and still slide it under the architrave you will need to remove some of the locking joint on the previous row.
Remove the lip along the tongue of the long edge using a sharp chisel. Apply glue to this edge. Slide the board to be fitted under the door architrave and then pull it back into place along the previous row.
Radiator pipe covers can either protrude through the floor or from the wall. If they are floor mounted then the Solid will need to be cut around the pipes with an expansion gap. Measure and mark the position of the pipes on the Solid board and cut the holes out using a 32mm spade drill bit. This should allow for the 15mm pipe and an expansion gap. Then remove the excess Solid to allow the board to be placed against the pipes. The area of Solid removed should represent a keyhole shape. Keep the off cuts of the Solid as these can be glued back into place once the plank is installed.
About the Author
Real Wood Flooring FAQs brought to you by the flooring experts at Wood Flooring 2U
If you would like any further information on solid wood flooring, engineered wood flooring, laminate wood flooring or advice on how to install a wooden floor, please don’t hesitate to get in touch, our knowledgeable team would be more than happy to help.
Bosch daredevil Spade Bit
| | IRWIN TOOLS Pointed Spade 53/8 x 16 inch Steel Pointed Spade 333014 $190 NEW $64.00 |
| | Irwin 88815 15/16″ SPADE BIT $3.59 |
| | Lot of 5 Irwin 88810 5/8″ Speedbor Blue Groove Spade Bit NEW FACTORY SEALED $13.68 |
| | IRWIN 6 PC. SPEEDBOR SPADE BIT SET W/BONUS SPEED BIT $15.99 |
| | Robt Bosch Tool Corp Accy DSB1009 3/4″ DAREDEVIL SPADE BIT $2.99 |
| | Robt Bosch Tool Corp Accy DSB1011 7/8″ DAREDEVIL SPADE BIT $3.43 |
| | Irwin 88712 3/4″ XL SPADE BIT $9.97 |
| | 3 PCE DRILL WOOD SPADE BIT SET 10,12,16MM POSTAGE PAID $6.93 |
| | 10 PCE DRILL WOOD SPADE BIT SET 6 10,12,16 18 22 25 32mm MEDALIST QUALITY SET $19.75 |
| | SPADE BIT SET 14 PCE DRILL WOOD 10mm-38MM QUALITY PACK $22.29 |
| | Irwin 4-Pack 1″ Speedbor Standard Length Spade Drill Bit Paddle $9.99 |
| | Bosch Dare Devil Spade Drill Bit 3/8″ NEW DSB1003 $2.98 |
| | Steelex Plus D2048 1-1/4-Inch TiN Coated Spade Bit $12.00 |
| | StSteelex Plus D2050 1-1/2-Inch TiN Coated Spade Bit $12.00 |
| | 4 DeWALT DW1416. 1-3/8 Rapid Load Quick Change Spade Bit (4) $10.81 |
| | 4 DEWALT DW1414 1-1/8″ Rapid Load Quick Change Spade Bit (4) $9.82 |
| | 4 DEWALT DW1406 9/16 ” Rapid Load Quick Change Spade Bit (4) $8.84 |
| | Irwin 88708 1/2″ XL SPADE BIT $9.03 |
| | 1/2″ WOOD SPADE DRILL BIT MADE BY POWERPOINT—NEW & NICE!!!!! $0.99 |
| | 1/2×3-1/2 Flat Boring Spade Bit 48-27-0070 Milwaukee $2.99 |
| | 4 Pack Irwin Blue Groove 1″ Spade bits $7.00 |
| | New England Twist Drill Wood Spade Bit 1-1/2″ WS6 – 112 $3.00 |
| | NEW 13pc Spade Bit Set W/softcase Black & Decker Pk Spade Bit Sets 71-536 $21.12 |
| | NEW Spade& Twist Drill Bit Sharpnr Ea. Drill Bit Sharpeners DDSB $162.39 |
| | 1-19/32 YG SPADE Drill bit Cutter TIP Tool Coolant Fed #3 SPLIT POINT S09312 $19.95 |
| | 6pc 12″Industrial spade paddle flat wood boring bit $14.99 |
| | 8Pc Set of Wood Boring Spade bits by Champion / Galaxy Made In USA $22.49 |
| | Milwaukee Accessory 49220185 6PC SPADE BIT SET $24.28 |
| | 7Pc Set of Wood boring Spade Bits by Champion / Galaxy Made in USA $16.49 |
| | 5Pc Set of Wood boring Spade Bits by Champion / Galaxy Made in USA $14.39 |
| | 7Pc Assortment of Wood boring Spade Bits by Champion / Galaxy Made in USA $18.49 |
| | Irwin Master Mechanic 1/2×16 Spade Wood Drill Bit $8.11 |
| | 6Pcs of 9/16″ Wood boring Spade Bits by Champion / Galaxy Made in USA $15.99 |
| | 6Pcs of 716″ Wood boring Spade Bits by Champion / Galaxy Made in USA $13.49 |
| | 11/16″ Wood boring Spade Bits by Champion Made in USA $15.99 |
| | 4Pcs of 1 3/8″ Wood boring Spade Bits by Galaxy Made in USA $16.99 |
| | Irwin 341008 8PC SPADE BIT SET $29.86 |
| | Large Indexable Spade Drill Bit Muskegon Tool HOLDER 14″ Long 2-1/2″ 3″ 4″ $74.50 |
| | 1-1/8″ Spade Bit Titanium Coated_The Hard Sizes To Find $2.79 |
| | 1-1/4″ Spade Bit Titanium Coated_The Hard Sizes To Find $2.99 |
| | 1-3/8″ Spade Bit Titanium Coated_The Hard Sizes To Find $3.19 |
| | 1-1/2″ Spade Bit Titanium Coated_The Hard Sizes To Find $3.39 |
| | (2) NEW in Package Spade Drill Bit Head s, Tips, ACME, 4″, HSS, # 137N-0400 $147.97 |
| | Lot of 17 IRWIN SPEEDBOR 9/16″ Flat Spade Wood Bits 88809 $15.00 |
| | Skil 13-Piece Spade Bit Set Drill/Drivers 95813 $9.97 |
| | 2 GEO WHALLEY SPADE DRILL BITS. SERIES C ALLIED BITS. DIAMETER 1.641S HSS Z600 $11.95 |
| | 2 AMEC SPADE DRILL BITS. SERIES B ALLIED BITS. DIAMETER 1 3/8″ HSS (Z606) $9.95 |
| | 3 ERIKSON SPADE DRILL BITS. SERIES AA-B ALLIED BITS. DIAMETER 1.375 HSS (Z607) $18.95 |
| | 3 AMEC SPADE DRILL BITS. SERIES B ALLIED BITS. DIAMETER 1 3/8″ COBALT (Z605) $18.95 |
| | 3 AMEC SPADE DRILL BITS. SERIES B ALLIED BITS. 1 5/16″ & 33 MM HSS (Z603) $15.95 |
| | 4 AMEC SPADE DRILL BITS. SERIES B ALLIED BITS. DIAMETER 1 3/8″ COBALT (Z604) $27.95 |
| | BLACK & DECKER 195 PIECE DRILL AND SCREWDRIVER SET MASONRY SPADE BITS WITH CASE $27.00 |
| | BLACK & DECKER 195 PIECE DRILL AND SCREWDRIVER SET BRAD POINT MASONRY SPADE BITS $27.00 |
| | Long & short round & Auger Shanks Wood working Auger drill & Spade bits 14pcs $48.50 |
| | Makita 6 Piece Spade Bit Set with Spurs 714171-A $15.00 |
| | PACK OF 5 x 24mm FLAT SPADE ZIP WOOD DRILL BITS $9.95 |
| | PACK OF 5 x 30mm FLAT SPADE ZIP WOOD DRILL BITS $10.98 |
| | 5 NEW CRAFTSMAN 4 PIECE SPADE BIT SET 20902 WITH THREADED TIP 3XFASTER $16.00 |
| | NEW Flat Boring Bit 3/4×3-1/2 Milwaukee Ea. Spade Bits 48-27-0080 $10.98 |
| | NEW Flat Boring Bit 7/8×3-1/2 Milwaukee Ea. Spade Bits 48-27-0085 $11.01 |
| | NEW Stubby Flat Boring Bit Set 6 Milwaukee Ea. Spade Bit Sets 49-22-0185 $30.93 |
| | NEW Flat Boring Set 8pc Milwaukee Each Spade Bit Sets 49-22-0175 045242180035 $33.74 |
| | NEW Flat Boring Bit 1/4×6 Milwaukee Ea. Spade Bits – Long 48-27-0251 $11.01 |
| | NEW 13 pc. Titanium Nitride Coated Spade Bit Set $15.99 |
| | 18 spade bits new in package 3 sets $10.00 |
| | 13/16″ SPADE DRILL BITS 6″ HEX SHANK – SET OF 5 – NEW $7.95 |
| | MADISON DUODEX COOLANT FEED SPADE DRILL #5MT SHANK W/2.625 BITS $225.00 |
| | GripTight Tools Quick Shank Prof. 6″ x 7/8″ Spade Bit $1.95 |
| | NEW Flat Boring Bit 1/2×3-1/2 Milwaukee Ea. Spade Bits 48-27-0070 $10.84 |
| | Lot of 5 – Irwin Speedbor 3/4″ Spade Bits (4 per Pk) – 20 total $40.00 |
| | Vermont American 1″ Wood Devil Spade Wood Boring Bit 14466 $5.64 |
| | Bosch Power Tools 3/8″ RapidFeed Spade Bit DLSB1003 $8.48 |
| | Vermont American 3/8″ X 4″ Stubby Length Black Max Wood Spade Bit 14485 $8.66 |
| | MILWAUKEE 48-27-0621 Carbon Steel Flat/Spade Wood Boring 5/8″ x 6-1/8″ Drill Bit $1.99 |
| | MILWAUKEE 48-27-0751 Carbon Steel Flat/Spade Wood Boring 3/4″ x 6-3/8″ Drill Bit $1.99 |
| | MILWAUKEE 48-27-0871 Carbon Steel Flat/Spade Wood Boring 7/8″ x 6-1/8″ Drill Bit $1.99 |
| | Century 88309 Wood Spade Bit 13/16″ $1.00 |
| | Mibro 278041 Spade Bit 13/16″ $1.49 |
| | Vermont American 14463 Spade Bit 13/16″ x 6″ $1.49 |
| | Craftsman 1-1/4 in. Self Feed Stubby Spade Bit $5.99 |
| | 6 Piece Flat Wood Boring Spade Drill Bits [Counter Sink Hole Cutters - Bit] $10.98 |
| | NEW 3/4″x16″ Spade Bit Each Spade Bits – Long DLSB1009 000346388862 $16.65 |
| | NEW 6″ Extension Spade Bit Each Spade Bit Extensions DSBE1006 000346390513 $11.56 |
| | Bosch 1/2-in x 6-in RapidFeed Spade Bit SB1005 NEW $10.98 |
| | HUGE LOT 41 NEW DRILLCO SPADE WOOD DRILL PADDLE BITS 1″ 1/2″ 1-3/8″ 7/8″ + $45.00 |
| | Makita 20mm Flat Wood Bit (Top Quality Spade Bit!!) $3.95 |
| | 7/8″ x 6″ Spade Bit $0.99 |
| | NEW DeWalt DW1588 6″ Wood Boring Spade Bit Extension $4.99 |
| | NEW DeWalt DW1589 12″ Wood Boring Spade Bit Extension $4.99 |
| | NEW Irwin 88706 3/8″ Extra Long Speedbor Spade Bit $8.99 |